DIY Tub Installation.
DIY Tub Installation.
Blog Article
We've unearthed this article relating to Installing A Bathtub below on the internet and think it made sense to talk about it with you on this site.
Setting up a bath tub isn't precisely brain surgery, but it does call for solid plumbing, woodworking, and often, tiling skills. Changing an old bathtub with a brand-new one is also a reasonably challenging task. If the old tub is conveniently accessible, the job can relocate quickly; if you need to open up a wall to eliminate the old bathtub and place the brand-new bathtub, the job is a lot harder. In either instance, the project is within a house handyman's abilities, although you will require a helper to leave the old tub as well as embeded in the new one. Make certain you have qualified on your own for the job as well as fit attempting it. As opposed to hiring a professional to take control of a halfway-completed project, it is much better to take into consideration employing one prior to you start. Chances are you may need an expert plumber to make tube links.
This article will assist you set up a new tub in your shower room if you have actually currently acquired a brand-new tub and don't need to alter the setup of your previous water pipes.
Your tools and material checklist must consist of the following:
Getting ready for the Setup
To start with, the sustaining framework provided with the bathroom must be fitted (if called for) according to the supplier's guidelines. Next off, fit the faucets or mixer to the tub. When suitable the faucet block, it is very important to make certain that if the tap includes a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is also sensible to fit a supporting plate under the faucets device to stop pressure on the bath tub.
Fit the adaptable tap connectors to the bottom of the two faucets utilizing 2 nuts as well as olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet through the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. See to it you make use of all of the supplied washers.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom must now be ready to be suited its last setting.
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your setup, then the first thing you should do is separate the water system. After doing so, turn on the faucets to drain pipes any water remaining in the system. The procedure of eliminating the existing faucets can be rather troublesome because of the restricted accessibility that is typically the case.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the faucets. Have a fabric all set for the staying water that will certainly come from the pipelines. Once the supply pipelines have been gotten rid of, use the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the single faucets from turning throughout this process. When the faucets have been eliminated, the holes in the bath/basin will have to be cleansed of any old securing substance.
Before carrying on to fit the brand-new faucets, compare the pipe links on the old faucets to the new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the new faucets to fit.
Mounting the Bathtub
Using the two wood boards under its feet, position the bath tub in the required setting. The wood boards are handy in evenly spreading the weight of the bathtub over the location of the boards instead of focusing all the weight onto 4 little factors.
The next goal is to make sure that the bath tub is leveled all round. This can be achieved by inspecting the level and also adjusting the feet on the tub up until the level reads level.
To mount taps, fit the bottom of the furthest versatile faucet adapter to the appropriate supply pipe by making a compression sign up with; after that do the very same for the other tap.
Turn on the water system and also examine all joints and new pipework for leaks as well as tighten them if needed. Load the bath tub as well as also check the overflow outlet as well as the typical electrical outlet for leakages.
Ultimately, deal with the bathroom paneling as described in the manufacturer's instruction manual. Tiling as well as sealing around the tub ought to wait until the tub has been utilized a minimum of once as this will settle it into its final setting.
Fitting New Taps
If the tails of the new taps are plastic, then you will need a plastic connector to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap and the various other end provides a link to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly need minimizing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next off, place the faucet in the installing hole in the bath/basin guaranteeing that the washers remain in area in between the faucet as well as the sink. Protect the tap in place with the supplier given backnut. As soon as the faucet is safely in place, the supply pipes can be attached to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with normal faucet adapters. The former type should be attached to the faucet ends first, tightening up only by hand. The supply pipelines can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the area where the bathroom meets the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is necessary as the fitting can move enough to fracture an inflexible seal, causing the water to penetrate the wall surface between the bath and also the tiling, causing problems with dampness and also feasible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to blend in your fixtures and also fittings. They are sold in tubes and also cartridges, as well as can securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of soaked paper or soft rope. Keep in mind to always fill the bath tub with water before sealing, to permit the motion experienced when the tub remains in use. The sealant can fracture relatively early if you do not take into account this activity before securing.
Additionally, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise easily available on the marketplace. It is a good idea to fit the tiles making use of waterproof or water resistant adhesive and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a devoted reader about A Step-by-Step Guide to Installing a Bathtub, I think sharing that piece of content was a good idea. Be sure to set aside a second to share this post if you enjoyed reading it. I am grateful for your time. Don't forget to pay a visit to our blog back soon.
Request Appointment Report this page